WI-101-L
INDOOR LTE CPE
INDOOR LTE CPE
WI-101-L 4G wireless router is designed for fast networking. The equipment adopts MTK industrial grade chipset, builtin
4G module, with hardware watchdog design, automatic disconnection, to ensure that the equipment is always online.
The operating temperature is - 10 ℃ ~ + 50 ℃. It supports a variety of VPN protocols (PPTP, L2TP), PPPOE, DHCP
and other network protocols. It is widely used in vehicle wireless networking, video monitoring, ATM fast networking,
water conservancy monitoring, vehicle networking, environmental monitoring and other fields.
| Software Features | WI-101-L |
| CPU processor | MTK7628 AN |
| DDR memory | 64M |
| DDR memory | 8M |
| Antenna | 4G antenna with 2 external 5dB omnidirectional antennas |
| 4G module Support | LTE FDD: B1/B3/B5/B8 LTE TDD: B34/B38/B39/B40/B41 WCDMA: B1/B5/B8 GSM: 900/1800MHz |
| Network interface | 2* 10 / 100 M adaptive LAN ports (auto MDI / mdix) |
| Power interface | DC 12V |
| SIM card slot | Nano SIM slot: 25 * 15mm |
| Status indicator | Power/LAN1/LAN2/SYS/4G/WIFI |
| Reset button | With this button, the parameter configuration of router can be restored to the factory value |
| DC power input | DC 12V / 1A power supply |
| POE power output | POE with 24V/48 V output power supply |
| Environmental standards | Working temperature: - 10 ~ + 50 ° C Working humidity: 10% ~ 95% RH (non condensing) Storage temperature: - 30 ~ + 80 ° C Storage humidity: 10% ~ 95% RH (non condensing) |
| 3G/4G | Display 3G / 4G connection status, SIM card status and network selection status |
| WAN | Display the connection status, protocol and connection time of WAN port |
| Wireless 2.4G | It shows the enabled / disabled status of wireless 2.4G, wireless SSID and the number of wireless connected devices |
| DHCP server | Display the enable / disable status, start IP address and end IP address of the DHCP server |
| system | Display firmware version, local time and system running time |
| 4G | 4G on / off button Network mode: automatic, only 3G, only 4G, only GSM and CDMA Network selection: automatic and manual selection |
| WAN mode | Alternative DNS, MAC, MTU PPPoE: user name, password, access concentrator, service name, MAC clone, MTU setting Static (fixed IP): IP address, subnet mask, default gateway, preferred DNS, alternative DNS, MAC clone, MTU setting |
| Wireless relay | The enable / close button displays the connection status and joins the network |
| Wireless 2.4G | Wireless 2.4G enable / close button, wireless SSID setting Encryption type (wpa-psk, wpa2-psk, wpa-psk / wpa2-psk) Wireless mode: 2.4GHz (802.11b), 2.4GHz (802.11g), 2.4GHz (802.11n), 2.4GHz (802.11b + G), 2.4GHz (802.11g + n), 2.4GHz (802.11b + G + n); Channel: automatic or 1-13 channel selection; Channel bandwidth: automatic, 20MHz, 40MHz select radio power: minimum, medium, maximum select connection number Hide network on / off button Isolate client enable / close button |
| LAN/WAN | LAN port and WAN port can be switched to bridge LAN port and WAN port |
| LAN | Set the internal and external network IP (such as WAN port connecting to the superior route). In order to avoid IP conflict, you can set the connection with the superior here Route different segments) |
| DHCP server | Modify local area network DHCP address |
| PPTP/L2TP | Client configuration connection supporting PPTP / L2TP protocol |
| VLAN | LAN port and WAN port can be switched to bridge LAN port and WAN port |
| QOS | To set the uplink and downlink bandwidth of the current network speed, the terminal equipment should be set according to the total bandwidth rate Place |
| DDNS | This setting can be implemented by domain name binding dynamic IP according to the default DDNS service provider registration account Process access management |
| Static routing | Support |
| Port forwarding | Internal port forwarding external port configuration item |
| DMZ | The device with specified intranet IP is open to the Internet |
| Network detection | Check whether 4G is connected to the Internet |
| Host name | Add the host name and MAC address of the terminal device |
| MAC address filtering | Set black and white list of terminal MAC access network |
| IP address filtering | Set the black and white list of terminal IP address to access the network |
| Domain name filtering | Set the black and white list of the domain names to be accessed |
| WPS | Set WPS on and off buttons |
| WiFi plan | Can customize the schedule to automatically turn WiFi on or off at a certain time |
| Remote management | Set the port of remote management, which can be accessed remotely through the known WAN port IP and port |
| Firmware update | Select the firmware file to upgrade for system upgrade |
| Backup / recovery | Back up the current configuration of the system and restore the saved configuration from the file |
| Centralized Management | NIMBUS Auto provisioning and Management |
| language | Set the language of the system, English or Chinese |
| watchcat | Watchcat allows you to set a periodic restart and / or when the network connection is disconnected for a specified period of time |
| Scheduled restart | The timing restart time can be configured in 0-23 hours and 0-59 minutes |
| restart | reboot system again |
| Return to factory | Restore the system configuration to the factory configuration |
| PING | Network conduction detection |
| TRACEROUTE | Traceroute sends packets to the destination host to detect whether each device on this path is on |
| NSLOOKUP | Query the DNS information of the host and whether the domain name resolution of the host is normal |